Journal of Environmental Chemical Engineering 10 (2022) 107394 Available online 15 February 2022 2213-3437/© 2022 Elsevier Ltd. All rights reserved.A review of heavy metals’ removal from aqueous matrices by Metal-Organic Frameworks (MOFs): State-of-the art and recent advances Nasrin Abdollahi a, Gholamreza Moussavi a,*, Stefanos Giannakis b a Department of Environmental Health, School of Medical Sciences, Tarbiat Modares University, Tehran, Iran b Universidad Polit´ecnica de Madrid, E.T.S. de Ingenieros de Caminos, Canales y Puertos, Departamento de Ingeniería Civil: Hidr´aulica, Energía y Medio Ambiente, Unidad docente Ingeniería Sanitaria,c/ Profesor Aranguren, s/n, ES-28040 Madrid, Spain A R T I C L E I N F O Keywords: Water contaminants Heavy metals Water treatment Adsorption Synthetic adsorbents A B S T R A C T Surface water and groundwater contamination by heavy metals is a global serious concern, which despite its well-known character, still lacks a decisive application to tackle its harmful side-effects. Among the various existing methods, due to its simplicity of the process and efficiency in removing heavy metals, adsorption is widely used in wastewater treatment. Recently, a new class of materials, metal-organic frameworks (MOFs), synthesized through hydrothermal or heating methods, sonochemistry, microwaves, and chemical ways, has been used as an effective adsorbent to remove toxic heavy metals from aqueous solutions, due to their unique properties such as their high chemical stability, high surface area, structural design, and reusability. In this review, we evaluated the various MOFs (including plain and modified MOFs, magnetic MOFs composites, etc.) for potential applications in the removal of the selected heavy metals. The values reported for the adsorption capacity of the selected heavy metal onto MOFs are in range of a few to several hundred mg/g. The mechanisms associated with these processes, i.e., physical and chemical adsorption, are discussed in detail; we assess the recent works of MOFs application in heavy metals removal, explain in-depth the physico-chemical processes governing adsorption, analyze the MOF categories and critically compare them with the existing technologies available. Overall, this review aims to gather the available knowledge on heavy metals’ adsorption by MOFs and act as a guide for the development of either new MOFs or further applications of adsorption. 1. Introduction Water is the primary source of all life. Although 72% of the earth’s surface is covered by water, only 0.5% is freshwater. Water resources’ quality is declining due to stressors, such as water pollution, exponential population growth, and climate change [1–3]. Water pollution is a sig- nificant concern due to massive urbanization and industrialization; it is estimated that around 1 billion people in the world do not have access to clean water, and about 2 million people die each year due to the contaminated water-related diseases [4]. Among water contaminants, inorganic substances, such as heavy metal ions, are among the biggest hazards to the environment and living organisms because they are highly toxic [5], rendering lots of potentially available water bodies not suitable for use. Therefore, controlling water pollution is one of the main ways to indirectly address water scarcity [6]. Heavy metals are known the natural elements with a high atomic weight and a density ≥ five times of water density. Elements such as lead (Pb), mercury (Hg), arsenic (As), cadmium (Cd), copper (Cu), chromium (Cr), boron (B), etc. have density approximately 5 kg/L [9]. Numerous agricultural, industrial, medical, and household usage of heavy metals have resulted in their widespread in the environment, raising concerns about their potential impact on the environment and human health [7]. Heavy metals are mobilized into the environment through several nat- ural processes, including spring waters, erosion, volcanic eruptions, bacterial activity, among others. These metals are usually present in small amounts in natural waters, but among them, many are toxic even at minuscule concentrations [8]. Specifically, metals such as lead, mercury, cadmium, arsenic, chromium, cobalt, selenium, nickel, and zinc are highly toxic even in otherwise minor levels. Many industries, especially in countries with loose or inexistent control frameworks, are discharging their metal-containing effluents into freshwater without sufficient treatment, and thus increase the quantities of heavy metals in water resources [10]. Human activities such as fossil fuel combustion, industrial processes, nutrition, and * Corresponding author. E-mail address: moussavi@modares.ac.ir (G. Moussavi). Contents lists available at ScienceDirect Journal of Environmental Chemical Engineering journal homepage: www.elsevier.com/locate/jece https://doi.org/10.1016/j.jece.2022.107394 Received 26 October 2021; Received in revised form 28 January 2022; Accepted 11 February

Journal of Environmental Chemical Engineering 10 (2022) 107394 2agricultural activities aggravate the aforementioned issue, damaging the anthroposphere: water, air, and soil are the main parts of the environ- ment affected by heavy metals pollution [11]. These heavy metals cycle back and return to harm the human species; through various processes, they can cause adverse effects on the human body; it can affect blood composition and damage the liver, lungs, kidneys, and other vital or- gans, causing several diseases [12]. Hence, the necessity to effectively intervene in this foul cycle, removing heavy metals as a preventive measure for environmental and living species protection is of outmost importance. 2. Current methods of heavy metals’ removal A range of technologies with proven capability is available for eliminating heavy metals from contaminated waters, including adsorp- tion, precipitation, membrane process, and ion exchange separation. The main features of these technologies are provided below. 2.1. Ion exchange The ion exchange method for heavy metals’ removal has advantages over other conventional methods due to its simplicity, high removal efficiency and capacity, as well as fast kinetics [13–16]. One of the key most helpful ion exchange reaction characteristics is its reversible character. In the reversible ion exchange process, the resin can be re- generated used repeatedly adding to the sustainability of the system. The ion exchange resin is a cross-linked polymer matrix to which exchangeable groups are bonded, and is stable in water [17]. Generally, resins are made in spherical, and strain-free form to resist physical destruction, they are stable in water and at high temperatures, and can be used in a wide range of water pH [18], and are classified in cationic and anionic converters, depending on the target ions’ charge. Some resins, such as sodium silicate, zeolite, acrylic and methacrylic resins, are among the most common materials to remove hazardous ions from wastewater; generally, the ion exchange method can reduce the amount of organic and inorganic pollutants by about 95% [13,19]. For example, the ion exchange process has been widely investigated for the removal of heavy metals from various matrices including water, wastewater, and sludge (indicatively, see [20,21]). 2.2. Precipitation The precipitation method is an effective technique for efficient eliminating metal ions and various organic pollutants from the contaminated water and wastewater. Chemical precipitation is a phys- icochemical process and is the most common method used for the removal of heavy metals in industrial application [22]. In this method, the solubility of contaminants is decreased, and the solid sediments are easily separated from water. In conventional treatment chains, precip- itation is the technique of choice for the removal of heavy metals and reduces the concentration of all metals. The solubility of metal pre- cipitates is the key to the success of this method. After application, the insoluble compounds formed by metals can be removed by filtration. Among the precipitation methods, sulfide and hydroxide are the two main methods that are currently used, while hydroxide precipitation is the most commonly used due to its simplicity and low cost [23–25]. An example of precipitation/separation applications are wastewater treat- ment from nickel and chromium plating industries and water recycling based on water softening and removal of phosphate from water [26]. In another study, for instance, the elimination of different heavy metals from water and wastewater was investigated by sulfur-containing pre- cipitation agents [27]. 2.3. Membrane process Membrane separation is already considered as a highly effective method in addressing energy and environmental challenges [28]. As far as the production of safe drinking water is concerned, membrane filtration is one of the efficient technologies that can be applied to remove water contaminants and ions. Typically, membranes are syn- thetic materials with high porosity that act as selective barriers and prevent the passage of some of the water components based on their size [29]. Membrane processes are considered for heavy metals’ removal, due to their range of advantages, including high efficiency and selec- tivity [14,30,31]. In general, there are two types of pressure-driven membrane process: (i) low-pressure membrane processes including microfiltration (MF) and ultrafiltration (UF); and (ii) high-pressure membrane processes including nanofiltration (NF) and reverse osmosis (RO) [32]. The development and application of RO and NF processes have been increased in recent years; they have been also used for removing heavy metals from the contaminated water. For instance, Ujang and Anderson [33] showed the possibility of using a low-pressure RO process to remove Zn(II) and Cu(II) from wastewater in the presence of EDTA as a chelating agent, while Tavani [34] reported the

Journal of Environmental Chemical Engineering 10 (2022) 107394 3efficiency, generation of a high amount of sludge, costly disposal, and sensitive operating conditions. As such, the underlying principles and the points that led to the recent advances in adsorptive technologies are further analyzed in the next sections. The examination of various ma- terials as adsorbents has been seen effective in previous works [e.g., 37–43], leading to high retention and potent promises. However, no technology is perfect, hence research has moved towards more advanced materials, to overcome the limitations shown by known nano- composites. Under this scope, MOFs have emerged as a promising method to effectively eliminate heavy metals from aqueous matrices. 3. Insights on the adsorption process: prevalent theories, isotherms, and models Adsorption can be considered either as a physical or a chemical process, due to the nature of the interactions between adsorbents and adsorbates. During physical adsorption, the sorbent and sorbates interact at the adsorbent surface through van der Waals forces. Since attachments are not immensely strong in physical adsorption, adsor- bents are easily regenerated by a simple intervention in the system, such as physical treatment, solvent exchange, and partial pH change. On the other hand, chemical adsorption occurs through chemical bonds crea- tion (including covalent bonds, materials, and ions) between the adsorbent and adsorbate surfaces, thus increasing the enthalpy, firm attachment and thus decreasing the reusability of the adsorbent [47]. Adsorption efficiency typically is evaluated by adsorption percent- age and capacity, which is described by kinetic models, as well as adsorption equilibrium isotherms. For the improvement of adsorption rate and the effective design of adsorption systems, proper under- standing and interpretation of adsorption isotherms are very important [48]. One of the most critical information needed to properly under- stand the adsorption process is the adsorption equilibrium, which can be achieved by modeling the isotherm data for its accurate generalization. The equilibrium adsorption efficiency (RE, %) and capacity (qe, mg/g) of heavy metals onto the adsorbent are calculated using the Eqs. (1) and (2), respectively, as follow [49,50]: RE (%) = C0 Ce C0 × 100 (1) qe (mg / g) = (C0–Ce) × V M (2) where C0 and Ce are the initial and equilibrium concentrations of the adsorbent in solution, V is the volume of the solution, M is the mass of the adsorbent, and qe is the equilibrium absorption value. Modeling of the adsorption isotherm data is a fundamental method for predicting and comparing adsorption performance, a key for the practical design of adsorption systems, expressing adsorbents capacities, and optimizing adsorption mechanisms [51]. Adsorption models are usually solved by linearization, and the level of model fitness is indi- cated by the linear regression coefficient (R2) usually indicates. For a two-parameter models, the value of determination coefficient for linear regression (R2) close to unity is considered the best fit [52]. Neverthe- less, it has been suggested that modeling isotherm data with linear analysis may cause a disparity between experimental data and pre- dictions. Several error functions have been developed and used to address this shortcoming. Simultaneous with the evolution of computer tools, the use of the nonlinear isotherm models has been used widely [53]. Nonlinear regression usually includes based on convergence criteria, the minimum or maximum error distribution between experimental and predicted data [52]. A good fitting of an adsorption isotherm can be very valuable since this non-linear curve describes the adsorption phenom- enon at a constant pH and temperature [54]. The different available adsorption isotherms are Henry’s [55], Hill-Deboer [56], Fowler-Guggenheim [57], Temkin [58], Dubinin-Radushkevich [59], Flory-Huggins [60], Hill [61], Halsey [62], Harkin-Jura [63], Jovanovic [64], Elovich [65], Kiselev [66], Redlich-Peterson [67], Sips [68], Toth [69], Koble-Carrigan [70], Kahn [71], Radke-Prausniiz [72], Freundlich [49], Langmuir [49], Jossens [73], Fritz-Schlunder [74], Baudu [75], Weber-Van Vliet [76], and Marczewski-Jaroniec [77]. Henry’s, Hill, Dubinin-Radushkevich, Freundlich, and Langmuir models are among the most commonly used isotherms because they can easily describe the experimental results acquired in a wide range of conditions (e.g., concentrations). 3.1. Henry’s isotherm Henry isotherm is the simplest adsorption isotherm by which the amount of adsorbate adsorbed on the surface is proportioned to the partial pressure of the adsorbent. Henry’s isotherm model provides a proper fit for adsorbing the relatively low concentrations of adsorbate so that all adsorbate molecules are separated from their nearest neighbors [55]. Therefore, the equilibrium concentration of adsorbate in adsorbed phase and the liquid are ex

Journal of Environmental Chemical Engineering 10 (2022) 107394 4adsorption energy. 3.4. Langmuir isotherm The Langmuir isotherm describes the adsorption of gas molecules onto the homogeneous solid surfaces, which shows one type of adsorp- tion site. Based on Langmuir’s theory, the adsorption process on the surface of a solid adsorbent is based on a kinetic principle, so that the rate of absorption and desorption must be equal [80]. Traditionally, this isotherm model has been used to quantify and compare the adsorption capacity of different bio-sorbents. The Langmuir isotherm is an experi- mental model assuming that the adsorption occurs as a monolayer in which the adsorption process is performed in specific, uniform, and equivalent local sites. There should be no spatial barriers and lateral interactions, even in adjacent locations, between adsorbed molecules [81]. Many researchers have implicitly and successfully extended the basic model of Langmuir isotherm to describe the adsorption of soluble species onto various adsorbents. The Langmuir model for absorption is as follows: qe = abCe 1 + bCe (8) where qe = the amount of adsorbate adsorbed per unit mass of adsorbent (mg/g), b = the Langmuir constant related to adsorption energy (l/mg), a = the maximum adsorption capacity of adsorbent (mg/g), and Ce= the equilibrium concentration of the adsorbate in solution (mg/L). 3.5. Freundlich isotherm The Freundlich isotherm explains the reversible and non-ideal multi- layer adsorption phenomenon. In this isotherm model, absorption heat and bonds do not need to be evenly distributed on the heterogeneous surface [82]. The Freundlich isotherm model is widely used in hetero- geneous systems, such as the adsorption of organic compounds or spe- cies that are highly interactive on molecular sieves or activated carbon. This adsorption isotherm model can be used also for describing the adsorption of gas contaminants onto heterogeneous surfaces [83]. The Freundlich isotherm is expressed as follows: qe = KfCe 1/n (9) where qe is the amount of adsorbent adsorbed per solid mass unit, Ce is the concentration of adsorbent equilibrium solution, Kf is The Freund- lich adsorption constant, and n is an experimental constant. As a partial conclusion, in order to understand, interpret, and predict the adsorption rate for specific applications, we need to understand the relationship between equilibrium adsorption results and theoretical or practical equations [84]. Kinetic studies are performed to understand the mechanisms of absorption better, determine the amount of adsorp- tion, while the kinetic models are helpful to determine the practical application of the adsorbent in the adsorption process. For instance, a slow adsorption rate indicates significant limitations and issues for practical applications [85]. The development of novel, highly efficient adsorbents pass through the deep understanding of the underlying mechanisms, from which the modification of existing materials or the synthesis of new ones is performed. Under this scope, the Metal Organic Frameworks (MOFs) have arisen as effective adsorbents that meet application demands through their exquisite physicochemical proper- ties. Before describing the application of MOFs in adsorption, a brief description of their categories and properties is provided. 4. Metal-organic frameworks (MOFs) as novel adsorbent materials In the past decades, various types of materials such as carbon-based, metal oxides, polymers, clay minerals, industrial and agricultural wastes, and others, have been used as adsorbents. The main disadvan- tages of some of these categories are their low selectivity, modest effi- ciency, and poor reusability [86–89]. Specifically for heavy metals, some of the most common categories of adsorbents used to remove them from aqueous media are natural materials, bio-sorbents, nano adsor- bents, nanocomposites, and MOFs, summarized in Fig. 1. Among these categories, MOFs have demonstrated exceptional qualities, since they increase the adsorption efficiency in the removal of heavy metals from contaminated water due to their large cavities and surface area, their unique adsorption sites, as well as their geometry. As such, these ma- terials have been gaining ground in research and development of tech- nical solutions (e.g., water/wastewater treatment), hence we have conducted and present a comprehensive analysis of using MOFs in the adsorption of heavy metals from aqueous matrices. But first, a presen- tation of their main properties, synthesis methods and prevalent cate- gories is provided. MOFs are a relatively new class of hybrid materials that have the potential for flexible design by controlling the functionalization of their pores. MOFs are crystalline compounds consisting of secondary struc- tural units (SBUs), metal ions or clusters, and organic linkers joined together by coordination bonds [90], as illustrated in Fig. 2. MOFs are composed of cluster or polyhedral po

Journal of Environmental Chemical Engineering 10 (2022) 107394 5react directly under specific conditions to achieve growth. The most common synthesis methods for producing MOFs are hydrothermal or solvothermal, sonochemical, microwave, and mechanochemical [9]. The hydrothermal or solvothermal method induces energy into the reaction system through electric heating. In sonochemistry, ultrasonic waves cause high temperature and pressure, which are associated with accelerated reactions, growth, by the collapse of the acoustic cavities. Microwave synthesis is facilitated by introducing said radiation as a heat Fig. 2. The schematic of both inorganic and organic parts for the synthesis of MOFs (permission to use was obtained from [90]). Fig. 3. The schematic of several MOF structures (permissions to use were obtained from [92–98]). N. Abdollahi et al.

Journal of Environmental Chemical Engineering 10 (2022) 107394 6source. And finally, in mechanochemical synthesis, a mill is used to grind mixtures of binding molecules and metal salts. MOFs can be divided into cationic, neutral, and anionic metal- organic frameworks, as well as bioMOFs. Examples of cationic metal- organic frameworks are Ag(4,4′-bpy)NO3 and Cu(4,4′-bpy)2(PF6) [99, 100]. In metal-organic compounds with a neutral framework, the host-guest interactions are weaker than these interactions in charged solids; a representative example is the MOF-5 compound [101]. In anionic metal-organic frameworks, usually their cavities are occupied by solvent guest molecules and organic cations, as seen in the [Me2NH2]2[Cd2(bpdc)3].4dma compound [102]. The methods typically used to determine the structure and identification of MOFs are elemental analysis, IR or UV-Vis spectroscopy, and NMR. The crystal structures in coordinated polymers are necessary in order to extract information about the physical properties of the structure. Thermal gravimetric analysis (TGA) and X-ray Diffraction (XRD) are among the suitable methods to evaluate the structural stability of MOFs. TGA shows the exit temperature of guest molecules and the network degradation tempera- ture, but does not provide any information about the porosity stability of the networks. The structural analysis provides direct information about their hardness-softness, flexibility, and also crystalline or amorphous phases at high temperatures. Finally, other advanced techniques can offer great insights into MOF structure and properties; many of these coordinated polymers are often single crystals of good quality for single-crystal XRD analysis (SCXRD), while XPS, IR, and NMR show structural changes during absorption [103]. The stability of MOFs in water is the prerequisite for their successful application in the removal of contaminants, including heavy metal ions in water. The weakest point in MOFs is the metal-ligand coordination bonds. Therefore, the stability of MOFs in water is strongly depends on the strength of coordination bonds [104]. Metal-ligand coordination geometry, porosity, crystallinity, and pore surface hydrophobicity are among the other factors affecting the water stability of MOFs. As such, the operating conditions, such as temperature and pH, must be consid- ered when assessing the stability of MOFs in water [105]. At this point, having acquired this information, the different types of adsorptions and their respective mechanisms within an application can be better understood. 5. Heavy metals’ removal by adsorption onto MOFs 5.1. Adsorption types and factors affecting MOFs’ adsorption performance Among the various materials, the use of MOFs as adsorbents for the adsorption of heavy metal ions from water, is highly desirable due to their porosity and high surface area. The adsorption process in porous adsorbents is divided in chemical and physical adsorption [106]. Physical adsorption is usually considered as surface adsorption while chemical adsorption is named as reactive adsorption. In the surface adsorption method, the adsorbed material is generally placed inside the adsorbent cavities via van der Waals forces, so that these adsorbents can be easily recycled through solvent exchange, calcination, or ultrasonic treatment. Chemical adsorption occurs when real chemical bonds are formed between the adsorbent and the absorbate. Therefore, surface adsorption for removing heavy metals is considered more desirable compared to other processes, due to its relatively low cost, ease of design, simple operation, and facile recovery of adsorbents. Recently, MOFs have been used to remove harmful substances through surface adsorption, due to their intrinsic features such as large cavities and their geometry [107], as well as the creation of specific adsorption sites [108]. In addition to the central metal [109], unsatu- rated coordination sites [110] and the loading of active species on MOFs [111] are effective in the interaction of harmful species and MOFs. Also, in addition to guest-host interactions, acid-base interactions [112], hydrogen bonds [113], and coordination with metal sites also importantly contribute in adsorption. 5.2. Underlying mechanisms of heavy metal’s adsorption onto MOFs The possible interactions between adsorbents (adsorbent active sites) and those absorbed in MOFs are one of the issues to be determined by adsorption mechanism. The assessment of the results of the available studies in literature have shown that four prevalent mechanisms exist in adsorption by MOFs, summarized in Fig. 4 and further analyzed in the following sub-sections. 5.2.1. Coordinative unsaturated sites If Lewis acid vacancy occurs on metal ions or cluster nodes, MOFs can contain coordinated unsaturated sites (CUS) or open metal sites (OMS). In 2000, Yaghi et al. [114] presented a Zn-MOF [Zn2 (BTC) (NO3)] with an open metal site. In these types of MOFs, some act

Journal of Environmental Chemical Engineering 10 (2022) 107394 7media, water molecules compete for hydrogen bonding sites. Therefore, in these systems it is not impossible, but multi-point interaction is necessary for efficient absorption. For example, Li et al. [123] showed that the As(V) adsorption capacity in MIL-53(Al) is 106 mg/g, and the proposed adsorption mechanism is based on a hydrogen bonding interaction. 5.3. Theoretical, lab-scale and real applications of MOFs for the removal of heavy metals In the following sections of the present work, we discuss in detail the various MOFs (including as-prepared and modified MOFs, magnetic MOF composites, and others), in their application to remove toxic metals such as lead, mercury, arsenic, chromium, cadmium, and boron. After the exhaustive presentation of the current literature, a detailed summary of the various MOFs used to remove each of these heavy metal ions is provided in Tables 2–7. 5.3.1. Lead Lead, as a toxic metal, enters the body of humans and animals through water, air, and food and accumulates in their vital organs. Lead is primarily distributed in the body of human to the liver, brain, kidneys, and bones. Most of the lead entered the body is excreted but some of it is stored in the teeth and bones. Children are more susceptible to lead poisoning than adults because they can absorb and retain it 3–5 times as much as adults [124]. Lead is used as an industrial raw material for manufacturing lead glass, photographic materials, storage batteries, pigments, matches, and explosives [125], and is known to be one of the most critical pollutants found in wastewaters from the production of essential compounds such as refineries, wastewaters from solvents res- idues, and post-production dyes. According to WHO standards, the provisional guideline value of Pb(II) in drinking water is 0.01 mg/L [126]. Due to its high toxicity, the concentration of lead needs to be reduced to a minimum, as low as ppb level. In this field, various methods have been used to remove lead, but among them, one the best approach is adsorption [127]. At present, the removal of lead ions using MOFs has become popular among re- searchers. Facultad et al. [128] used MOF-5 for the elimination of Pb(II) ions from aqueous media through the interaction with BDC2-, observing a maximum absorption capacity of 659 mg/g. Further, Yin et al. [129] prepared Zr-MOFs by a rapid microwave-promoted method within 3 min for Pb(II) adsorption and the maximum adsorption capacity for Fig. 4. The schematic outline of the mechanisms for adsorption of contaminants using MOFs. Table 2 Comparison of the adsorption capacity of various MOFs for Pb(II) ions. MOF pH Isotherm model Kinetic model Adsorption capacity (mg/ g) Surface area (m2/ g) Time (min) Efficacy factor (mg/ m2) Ref. MOF-5 5 Langmuir PSO 659 3800 30 0.17 [128] UiO-66-NH2 6 Langmuir PSO 135 876 3 0.15 [129] Fe3O4@Cu3(btc)2 5.9 Langmuir PSO 215 552 120 0.38 [130] TMU-31 5 Langmuir PSO 909 – 5 – [132] TMU-32 5 Langmuir PSO 909 432 5 2.10 [132] Fe-BTC/PDA-19 – – – 394 1134 1 0.34 [133] MMMT@Zn-BDC 6 Langmuir PSO 725 74.35 90 9.74 [134] (Mn(BDC)(H2O)2) 5 Langmuir PSO 104 9 360 11.54 [135] Tb-MOF 5.5 Langmuir PSO 547 56.72 10 9.64 [136] MOF-5-CMC > 5 Langmuir PSO 323 – 120 – [137] MIL-101(Fe)/GO 6 Langmuir PSO 129 377 15 0.34 [138] TMU-56 7 Langmuir PSO 1130 650 0.3 1.73 [139] Fe3O4@TMU-32 7 Langmuir PSO 1600 358 20 4.46 [141] MOF-MA 4 Hill PSO 510 296 960 1.72 [142] nFe3O4@MIL88A(Fe)/ APTMS 6 Langmuir PSO 536 62.21 20 8.61 [143] NH2-SiO2@Cu-MOF 6 Langmuir PSO 167 1111 10 0.15 [144] UiO-66-EDA 6 Langmuir PSO 244 – – – [145] N. Abdollahi et al.

Journal of Environmental Chemical Engineering 10 (2022) 107394 8the yellow UiO-66-NH2 was calculated to be 135 mg/g. Ke et al. [130] studied a novel type of thiol-functionalized magnetic core-shell MOF microspheres for selective removal of Pb(II) from wastewater with a maximum adsorption capacity of 215 mg/g at room temperature. Shooto et al. [131] studied the adsorption capacity of a Fe-MOF for the removal of Pb(II) ions and reported the highest adsorption of 85.3% at a concentration of 60 ppm Pb(II); the adsorption decreased at higher concentrations due to the reduction of free pore space and active sites. The urea-based organic frameworks (TMU-31 and TMU-32) was inves- tigated as highly effective and rapid adsorbents to remove Pb(II) from water; an adsorption capacity of 909 mg/g in less than 5 min was ach- ieved by these two structures [132]. Such a high adsorption capacity was related to the chemical bond formed between the oxygen and nitrogen atoms of the urea fraction and Pb(II) ions [132]. The performance of a MOF/polydopamine composite (Fe-BTC/PDA) was evaluated for the removal of Pb(II) ions from real water samples with an adsorption capacity of 394 mg/g for Fe-BTC/PDA-19 [133]. The better performance of the composite compared to plain MOF was attributed to the high density of heavy metal scavenging groups on the polymer backbone, playing an essential role in the adsorption process [133]. Shen et al. [134] studied the adsorption of Pb(II) in aqueous solution by Zn-BDC coated with magnetic montmorillonite reporting an adsorption capacity above 725 mg/g, and the transfer of electron pairs between the adsorbent and the adsorbate was the governed mechanism [134]. A manganese-based MOF (Mn(BDC)(H2O)2) prepared by a mi- crowave method was tested for the adsorption of Pb(II) ions from an aquatic medium, and the maximum adsorption capacity was measured to be 104 mg/g [135]. Hongshan et al. [136] prepared Tb-MOFs by assembling carboxylate-based ligands and Tb3+ under solvothermal conditions, for the efficient adsorption of Pb(II) with a maximum adsorption capacity of 547 mg/g. Jin et al. [137] synthesized a car- boxymethylcellulose/MOF (MOF-5–CMC) for the adsorption of Pb(II) from an aqueous solution under various experimental conditions and the maximum adsorption capacity was 323 mg/g under the optimum con- ditions [137]. The efficacy of the MIL-101(Fe)/GO nanocomposite for the removal of Pb(II) was examined and the adsorption capacity of 129 mg/g with a fast adsorption equilibrium time (15 min) was achieved, which was attributed to the unique sandwich structure and synergistic effect of MIL-101(Fe) and GO [138]. Afshariazar et al. [139] evaluated the ca- pacity of TMU-56 to adsorb Pb(II) ions from water with the maximum absorption capacity to be 1130 mg/g. It was reported that the TMU-56 was an effective and practical adsorbent due to important factors such as high porosity, large enough cavity size, abundant metal chelating sites, and proper geometry of the coordination sites [139]. Gerard et al. [140] investigated the adsorption capacities of UiO-66 and UiO-66-(SH)2 MOFs as plain and composited with CeO2 for the removal of Pb(II) ions from water, and the Pb(II) adsorption efficiency was highest for UiO-66-(SH)2 (97%) and CeO2@UiO-66-(SH)2 (96%). The magnetization of this composite did not negatively affect its adsorption potential [140]. Furthermore, Abdollahi et al. [141] syn- thesized a Fe3O4@TMU-32 composite through an in-situ synthesis method to remove Pb(II) ions with an adsorption capacity 1600 mg/g for Pb(II) by electrostatic interaction mechanism. Wang et al. [142] studied mercaptosuccinic anchored MOF (MOF-MA) for Pb(II) adsorp- tion and found the maximum adsorption capacity of 510 mg/g via the coordination and electrostatic interaction mechanism [142]. The adsorption of Pb(II) onto nFe3O4@MIL-88A(Fe)/APTMS material was evaluated and maximum adsorption capacity of 536 mg/g was reported. The presence of amino groups in the structure of nFe3O4@MIL-88A (Fe)/APTMS played a vital role in increasing and improving the binding characters of the target metal ions; nFe3O4@MIL-88A(Fe)/APTMS may be interacted with Pb(II) ions by the formation of coordinate bonds at pH> 4, because the adsorbent surface charge is negative at pH> 4 [143]. Mohammadi et al. [144] synthesized NH2-SiO2@Cu-MOF as an adsorbent to remove Pb(II) ions from the aqueous solution, achieving a maximum adsorption capacity at 167 mg/g. The study of the mechanism has shown that the adsorption process probably proceeds through the coordination interaction between Pb(II) and N in the amino group (–NH2) [144]. The potential of UiO-66-EDA was examined for the adorption of Pb(II) ions from water and a maximum adsorption capacity of 244 mg/g was observed. Adsorption of Pb(II) ions depended to the electron sharing, electron exchange, electrostatic, and covalent in- teractions between Pb(II) ions and abundant functional groups at the UiO-66-EDA sur

Journal of Environmental Chemical Engineering 10 (2022) 107394 9Table 4 Comparison of the adsorption capacity of various MOFs for As(V) and As(III) ions. Ion MOF pH Isotherm model Kinetic model Adsorption capacity (mg/g) Surface area (m2/g) Time (min) Efficacy factor (mg/m2) Ref. As(V) Fe3O4@MIL-101-Cr 7 Langmuir PSO 80 2270 – 0.03 [156] MIL-100(Fe) 7 Langmuir – 110 1369.6 60 – [157] RT-Zn-MOF-74 7 Langmuir PFO 99 – 60 – [158] HT-Zn-MOF-74 7 Langmuir PFO 49 – 60 – [158] AUBM-1 7 Langmuir PSO 103 310 300 0.33 [159] Fe-MIL-88A 5 Langmuir PSO 145 – 20 – [161] La-BA – Langmuir PSO 372 3.50 30 106.3 [163] La-BDC 7 Langmuir PSO 552 5.30 100 104.18 [163] As(V) La-BTC – Langmuir PSO 40 12.6 360 3.15 [163] Fe2CO1MOF-74 4.3 Langmuir PSO 292 147.82 – 1.97 [164] Zn-MOF-74 7 Langmuir PSO 325 604 150 0.53 [165] Fe3O4@UiO-66 7 Freundlich PSO 73 124.8 240 – [166] Fe/Mg-MIL-88B(0.5) 7 Langmuir PSO 304 360 60 – [168] GUT-3 3 Langmuir PSO 33 – 300 – [169] HP-UiO-66 6 Langmuir PSO 249 433 360 0.57 [170] BUC-17 10 Langmuir PSO 129 – 720 – [171] UiO-66–36TFA 7 Langmuir PSO 200 1690 180 0.11 [172] FeO4-Car-MOF 8.5 Langmuir PSO 94 – 180 – [173] MIL-100(Fe)/rGO/D-MnO2 2 Langmuir PSO 162 219.3 120 – [174] MOF-76(Y) 10 Langmuir PSO 188 919.43 30 – [176] MOF-76(Y)-Ac 10 Langmuir PSO 201 980.33 30 – [176] MIL-125(Ti) 3 Langmuir PSO 46 1422.03 20 – [178] As(III) Fe3O4@MIL-101-Cr 7 Langmuir – 122 2270 – 0.05 [156] MIL-53(Al)-GO 6 Langmuir PSO 65 1150 60 0.05 [160] Fe3O4@ZIF-8 8 Langmuir PSO 100 1133 240 0.09 [162] Fe2CO1MOF-74 4.3 Langmuir PSO 267 147 – 1.81 [164] Zn-MOF-74 12 Langmuir PSO 325 604 150 0.53 [165] Fe3O4@TA@UiO-66 7 Langmuir PSO 98 130.3 120 0.7 [167] MIL-100(Fe)/rGO/D-MnO2 2 Langmuir PSO 193 219.3 40 0.8 [174] Zn-MOF 5 Langmuir PSO 32 89.8 240 0.35 [175] Zn-MOF-74/rGO/PAM 10 Langmuir PSO 282 81.1 15 3.4 [177] MIL-125(Ti) 3 Langmuir PSO 40 1422.03 20 0.03 [178] N. Abdollahi et al.

Journal of Environmental Chemical Engineering 10 (2022) 107394 10Under the scope of Hg removal, there have been numerous reports of mercury adsorption using MOF adsorbents and/or their composites. In this context, Xiong et al. [147] studied MOF-74 for the removal of Hg(II) from ultra-low concentrations in aqueous solutions. The adsorption of Hg(II) on MOF-74-Zn increased with increasing pH, and high tempera- ture has positive effects on Hg(II) uptake, so it is an endothermic reac- tion. The maximum adsorption capacity was 63 mg/g. In this MOF, the hydroxyl groups in the pore wall can coordinate with Hg(II) ions, thus acting as strong sites for the chemical adsorption of Hg(II) [147]. Ke et al. [130] studied Fe3O4@Cu3(btc)2 core-shell magnetic microspheres for the removal of Hg(II) from mixed metal ions wastewater, and the maximum adsorption capacity was 348 mg/g [130]. Zhao et al. [148] prepared the MIL-101(Cr) to remove elemental mercury from sintering flue gas. The adsorption capacity of their MOF was 127 mg/g; the removal efficiency of Hg(II) using MIL-101(Cr) improved with increasing oxygen content and temperature. Investiga- tion of the mechanism revealed that Hg0 is first adsorbed on the surface of Mil-101(Cr) and then oxidized by the open metal site Cr3 + [148]. Chen et al. [149] studied DUT-67(Zr) for the adsorption of methylmer- cury and mercury ions from an aqueous solution. The adsorption effi- ciencies obtained for CH3Hg+ and Hg(II) at pH= 6 and 55 ◦C were, 55% and 90%, respectively. In addition, this MOF was used to remove CH3Hg+, and Hg(II) in real water samples, and the adsorption efficiencies increased from 30% to 77% and from 69% to 90%, respec- tively. Mechanistically speaking, the results showed that there is both chemisorption and physisorption between the DUT-67(Zr) and Hg(II), while between DUT-67(Zr) and CH3Hg+ there is the only physisorption [149]. Liang et al. [150] prepared an In2S3@MIL-101 MOF for rapid removal of Hg(II) from water. This composite can remove 99.95% of the Hg(II) from wastewater in 1 min with a very high distribution coeffi- cient; the maximum adsorption amount was 518 mg/g. In this MOF, many S atoms on the In2S3@MIL-101 composite surface can interact with Hg(II) ions and increase the amount of adsorption [150]. Furthermore, Hakimifar et al. [132] prepared TMU-31 and TMU-32 through mechanosynthesis. These two MOFs contained urea functional groups, resulting in the efficient, rapid, and selective adsorption of Hg (II) ions from wastewater, and the adsorption capacity was 476 mg/g within 15 min [149]. The results showed that these two MOFs demon- strate similar efficacy in removing Hg(II) ions from water. The presence and the proper geometry of urea functional groups provided good co- ordination for Hg(II) ions within the porous channels in the prepared MOFs [132]. In another study, Daniel et al. [133] studied Fe-BTC/PDA for selective, rapid, and efficient adsorption of Hg(II) ions from real water samples. They found that the adsorption capacity for Hg(II) using the Fe-BTC/PDA-42 composite was 1634 mg/g, which is almost ten times that of unmodified Fe-BTC [133]. Table 5 Comparison of the adsorption capacity of various MOFs for Cr(VI) ions. MOF pH Isotherm model Kinetic model Adsorption capacity (mg/g) Surface area (m2/ g) Time (min) Efficacy factor (mg/ m2) Ref. GO-CS@MOF[Zn(BDC(DMF)] 3 Langmuir PSO 145 37 360 3.91 [185] UiO-66-NH2 6.5 Langmuir PSO 32 710 1400 0.04 [186] BUC-17 4 Langmuir PSO 121 2.39 480 50.62 [187] UiO-66 3 Langmuir PSO 35 800 45 0.044 [188] ZIF-8 3 Langmuir PSO 150 1050 45 0.14 [188] Amino-functionalized MIL-101 (Cr) 3.51 Dubinin-Radush kevich PFO 44 2000 120 0.022 [190] nFe3O4@MIL-88A(Fe)/APTMS 2 Langmuir PSO 1092 62 20 17.61 [143] Table 6 Comparison of the adsorption capacity of various MOFs for Cd(II) ions. MOF pH Isotherm model Kinetic model Adsorption capacity (mg/ g) Surface area (m2/ g) Time (min) Efficacy factor (mg/ m2) Ref. TMU-16-NH2 6 Freundlich PSO 127 – 30 – [194] PAN-MOF-808 4.5 Langmuir PSO 225 939 10 0.23 [195] MOF-199 5 Langmuir PSO 87 1321 60 0.06 [196] CMOF-199 5 Langmuir PSO 113 1196 40 0.09 [196] Y-CD MOF-NPC 7 Langmuir PSO 141 11 30 12.80 [197] MnFe2O4-TiO2-UiO-66 5 Langmuir PSO 783 792 63 0.98 [198] (Mn(BDC)(H2O)2) 5 Langmuir PSO 132 9 360 14.62 [135] ZIF-8-mmen 6 Langmuir Lagergren 1000 970 90 1.03 [200] Ag-Fe MOF 7 Langmuir PSO 265 1150 65 0.23 [201] (ED-MIL-101(Cr)) 6 Langmuir PSO 63 766 180 0.08 [202] La-Succinate 5 Freundlich – 3 364 45 0.006 [203] Y-Succinate 7 Freundlich – 2 260 15 0.005 [203] nFe3O4@MIL-88A(Fe)/ APTMS 6 Langmuir PSO 693 62 20 11.17 [143] UiO-66 7 Freundlich PFO 112 1304 – 0.085 [204] UiO-66@mSi-sH 7 Langmuir PSO 212 443 – 0.47 [204] UiO-66@mSi-SO3H 7 Langmuir Elovich 410 126 – 3.25 [204] UiO-66-EDA 6 Langmuir PSO 217 – – – [145] Table 7 Comparison of the adsorption capacity of various MOFs for B ions. MOF pH Isotherm model Kinetic model Adsorption capacity (mg/g) Surface area (m2/g) Time (min) Effic

Journal of Environmental Chemical Engineering 10 (2022) 107394 11Liu et al. [151] studied the Hg(II) adsorption efficiency using MOF-808 and MOF-808/AO in an aqueous media. The maximum adsorption capacities for the MOF-808/AO and MOF-808 reported to be 384 and 344 mg/g, respectively. Thus, MOF-808/AO has shown higher adsorption efficiencies in all conditions, which could be due to the strong interactions between AO groups and Hg(II) ions [151]. Yang et al. [152] synthesized a Zr-MSA for the adsorption of Hg(II). The Zr-MSA had very high adsorption potential (734 mg/g) and rapid kinetics (with a removal of 99.9% Hg(II) in 5 min), related to the strong affinity between alkyl thiol and Hg(II) ions [152]. Furthermore, Abd et al. [135] studied the (Mn(BDC)(H2O)2) for the adsorption of Hg(II) ions from an aquatic medium. The removal percentage of Hg(II) ions by this Mn-MOF increased with increasing solution temperature, the adsorption process was endothermic, and the maximum adsorption capacity was 96 mg/g [135]. Shayegan et al. [153] prepared PCN-221 for Hg(II) adsorption from aqueous medium, and the adsorption capacity of 233 mg/g was obtained in less than 30 min at pH = 7. In this MOF, a nitrogen-functionalized group in the porphyrin ligand contributed in the adsorption Hg(II) [153]. Wang et al. [142] studied a novel zirconium-based MOF adsorbent (MOF-MA) to enhance adsorption capacity of Hg(II) to around 1080 mg/g. The sulfur-containing functional groups played a crucial role in the whole adsorption process. The evaluation of the absorption mechanism showed coordination and electrostatic interaction between the Hg(II) and sulfur groups [142]. Abdollahi et al. [141] developed a Fe3O4@TMU-32 nanocomposite through encapsulation of Fe3O4 nano- particles in the TMU-32 framework, showing a mercury adsorption ca- pacity of 905 mg/g. Examination of the adsorption mechanism revealed that a higher negative charge on the surface of Fe3O4@TMU-32 nano- composite leads to strong electrostatic interactions between Hg(II) metal ions and Fe3O4@TMU-32 surface [141]. Also, due to the high density of urea (C––O and N-H) and Fe-O interaction sites and their homogeneous distribution, Hg(II) ions interacted with the Fe3O4@TMU-32 composite [141]. Gerard et al. [140] prepared UiO-66, CeO2@UiO-66, UiO-66-(SH)2, and CeO2@UiO-66-(SH)2 for the removal of Hg(II) ions, which showed adsorption efficiencies of 15%, 1%, 91%, and 93%, respectively. Also, the study of Hg(II) ions adsorption using CeO2/- Fe3O4@UiO-66-(SH)2 showed that the Hg(II) metal adsorption capacity is similar to the non-magnetic particles, and easily was separated from the treated solution by an external magnet [140]. Comparing the different MOFs used for mercury removal (Table 3), it can be provisionally concluded that the Fe-BTC/PDA presented the highest amount of adsorption [133]. Fe-BTC binds to polydopamine (PDA) via Fe3+ open metal sites under spontaneous polymerization. PDA, which is bonded on the inner MOF surface, gains extrinsic porosity, as a result, the composite adsorbed 1634 mg/g of Hg(II) ions and removes over 99% of these ions from the 1 ppm solution [133]. There- fore, the high density of the heavy metal scavenging groups on the polymer backbone is the main factor in high removal capacity. 5.3.3. Arsenic Arsenic, as a chemical constituent, is widely used in different in- dustries such as agriculture, electronics, medicine, wood preservation, and metallurgy [154]. However, As is a naturally occurring compound and not an exclusive xenobiotic/anthropogenic contaminant since it is present in both the organic and inorganic forms in the Earth’s crust [155]. A Provisional guideline value of 0.01 mg/L was determined for arsenic in drinking water [126]. Long-term consumption of drinking water containing inorganic arsenic in concentrations above 50 μg/L can increase the risk of kidney, skin, and bladder cancer [36]. Therefore, research and development of arsenic removal technology are critical and various potent technologies have been developed over the years. Folens et al. [156] prepared a Fe3O4@MIL-101–Cr for eliminating As species from water. The adsorption capacities for As(III) and As(V) species were 122 and 80 mg/g, respectively. This composite performs better than the pristine MIL-101(Cr) and pure Fe3O4, despite its low porosity. Fe3O4 encapsulated in MIL-101 performed better even in real groundwater and surface water samples and has high removal effi- ciencies; therefore, these materials can also be used in real water [156]. Also, Jianhua et al. [157] studied MIL-100(Fe) to remove As(III) from water, and the maximum adsorption capacity was 110 mg/g. This framework not only provides appropriate size cavities for AsO43- to enter, but unsaturated Fe(III) sites can also easily adsorb AsO43- [157]. Furthermore, Tarboush et al. [158] prepared the Zn-MOF-74 via room temperature precipitation (RT-Zn-MOF-74) and solvothermal (HT-Zn-MOF-74) procedures for the removal

Journal of Environmental Chemical Engineering 10 (2022) 107394 12efficient adsorption of As(V) from arsenic-laden wastewater using GUT-3 with a maximum adsorption capacity of 34 mg/g was reported by Zheng et al. [169]. Hirshfeld surface analysis showed that H-H, C-H, and O-H bonds constitute the majority of intermolecular interactions, and chemical adsorption is the primary mechanism of As(V) adsorption by GUT-3 [169]. Rongming et al. [170] prepared a hierarchical porous HP-UiO-66 for arsenic removal, which was water-stable and had an adsorption capacity of 249 mg/g. The results of the adsorption mecha- nism analysis showed that arsenic is adsorbed through the occupation of unsaturated zirconium atoms [170]. Pang et al. [171] synthesized BUC-17 for the efficient removal of As(V) and its maximum adsorption capacity was 129 mg/g. Possible adsorption mechanisms in this study included ion exchange and electrostatic interactions [171]. Assaad et al. [172] studied UiO-66 nanoparticles with various defect concentrations and examined them as adsorbents for As(V) removal from water and the results indicated that UiO-66–36TFA has the highest As(V) uptake (200 mg/g). In this MOF, the removal of As (V) increased by either increasing the defect amounts, increasing the amount of acid, or moderating the acidity because it lead to more available free sites for binding As(V) [172]. A novel magnetic bio-metal organic framework (Fe3O4-Car-MOF NPs) was made by Keykhaee et al. [173] for the adsorption of arsenic from aqueous solutions, and the maximum adsorption capacity was 94 mg/g at room temperature [173]. Sittipra- nee et al. [174] synthesized a MIL-100(Fe)/rGO/D-MnO2 for adsorption of As(V) and As(III) from aqueous solutions and the maximum adsorp- tion capacities of As(V) and As(III) were 162 and 193 mg/g, respec- tively. The mechanisms governing adsorption were electrostatic interaction, oxidation, and inner-sphere surface complexation [174]. The maximum capacity of Zn-MOF for the adsorption of As(V) was 32 mg/g, and the mechanism was that Zn-MOF interacts with AsO43- through poor chemical coordination and ion exchange [175]. Zongchen et al. [176] synthesized MOF-76(Y) and MOF-76(Y)-Ac for the removal of As(V) from alkaline smelting wastewater, and the maximum adsorption capacities of MOF-76(Y) and MOF-76(Y)-Ac were deter- mined to be 188 mg/g and 201 mg/g, respectively. The mechanism of adsorption was the Y-O-As inner-sphere coordination, through ligand exchange between As(V) and the BTC linkers connecting with Y nodes [176]. Zn-MOF-74/rGO/PAM was synthesized by Sittipranee et al. [177] for the removal of As(III) from water and the maximum adsorp- tion capacity was 282 mg/g. Zhongmin et al. [178] studied removal of As(III) and As(V) by MIL-125(Ti) and reported a maximum adsorption capacity of 40 and 46 mg/g for As(III) and As(V), respectively. As(III) and As(V) could easily replace the terephthalic acid ligand through competitive coordination and bind to the Ti active site of MIL-125(Ti) [178]. As per comparison of the efficacies among the MOFs studied for the adsorption of As(V) ions (Table 4), La-BDC has shown the highest adsorption because, in La-BDC, central metal has a 9-fold coordination wherein three oxygen atoms from the hydroxyl groups and six oxygen atoms from the BDC form a distorted dodecahedron, and the free hy- droxyl groups are responsible for adsorption of AsO43 . On the other hand, the study of different MOFs for the adsorption of As(III) ions showed that the Zn-MOF-74/rGO/PAM has the highest amount of adsorption because (1) rGO increased the surface area, created more active sites, facilitated rapid electron transfer between adsorbents and adsorbates, and thus making the adsorption process more efficient; (2) a large number of functional groups -OH from Zn-MOF-74 and functional groups -NH2 from PAM can act as binding sites for As(III) ions. 5.3.4. Chromium Chromium can exist in two forms in aqueous systems, namely trivalent Cr(III) or hexavalent Cr(VI). Cr(VI) is significantly more toxic than Cr(III) [179,180] and can be found in wastewater from many in- dustrial activities, such as leather tanning, metal processing, plating, steel making, paint production, paper production, and so on [181–184]. A provisional guideline value of 0.05 mg/L was set for chromium in drinking water [126]. Cr(VI) causes serious problems such as perfora- tion in the nasal septum, dermatitis, bronchitis, and cancer [9]. In this regard, different MOFs are examined for effective chromium removal and prevention of Cr-related illnesses. Samuel et al. [185] prepared GO-CS@MOF for the adsorption of Cr (VI) ions from aqueous solutions. The maximum sorption capacity was obtained at 145 mg/g, which is better than CS, GO, and CS-GO nano- particles. As well, this composite for real wastewater showed an adsorption capacity of 85%. The decrease in the percentage of adsorp- tion in real wastewater may be due to organic matter, salt, and etc

Journal of Environmental Chemical Engineering 10 (2022) 107394 13MOF-199, and CMOF-199, respectively. The high adsorption capacity of CMOF-199 was attributed to the incorporation of the abundant chemical functional groups present in CNO, and to the higher surface area and porous nature of MOF-199 in CMOF-199 [196]. Liu et al. [197] investigated the adsorption of Cd(II) by green cyclodextrin MOF-based nanoporous carbon (Y-CD MOF-NPC) and re- ported the maximum adsorption capacity of 141 mg/g. The ion ex- change of oxygen-containing functional groups (-OH and -COO-) played the main role in the binding of Cd(II) through electrostatic interaction [197]. Furthermore, Nasehi et al. [198] reported the maximum adsorption capacity of 783 mg/g for the adsorption of Cd(II) by UiO-66-MnFe2O4-TiO2 magnetic nanocomposites. They found that the adsorption of Cd(II) ions occurred through a chemical process and Cd(II) ions were adsorbed through O-H groups in UiO-66 [198]. Yusuff et al. [199] studied Cu-MOF for the removal of Cd(II) from aqueous solution with the adsorption capacity of 219 mg/g. The presence of active sites on the adsorbent surface led to an electrostatic interaction between the adsorbent and the adsorbate [199]. Abd et al. [135] prepared a manganese-based MOF (Mn(BDC)(H2O)2) for adsorption Cd(II) ions from aquatic medium and the results showed that the maximum adsorption capacity is 132 mg/g [135]. Binaeian et al. [200] studied the performance of Cd(II) adsorption using ZIF-8-mmen and demonstrated that the maximum capacity of the MOF for adsorbing Cd(II) ions was as high as 1000 mg/g. The thermo- dynamic parameters showed that the process of adsorption (phys- isorption) of Cd(II) using this nanocomposite was spontaneous and endothermic [200]. Furthermore, Yazeed et al. [201] studied Ag-Fe MOF for the removal of Cd(II) with the maximum adsorption capacity of 265 mg/g. Due to the synergistic contribution between Ag and Fe, the adsorption rate and capacity of Cd(II) on Ag-Fe MOF was high [201]. The mechanism study confirmed the significant role of the electrostatic interactions in the adsorption process [201]. Elaiwi et al. [202] syn- thesized ED-MIL-101(Cr) for the adsorption of Cd(II) ions and obtained the maximum adsorption capacity of 63 mg/g. it was deduced that amine groups could provide binding sites in the MOF for Cd(II) ions to be adsorbed [202]. Fajrin et al. [203] studied La-succinate MOF and Y-succinate MOF as adsorbents for Cd(II) metal ions, and the maximum adsorption capacities for La-succinate MOF and Y-succinate MOF were 3 and 2 mg/g, respectively. This difference in the amount of adsorption could be due to the difference in the surface area of the two MOFs; the surface area of the La-succinate MOF was larger than that of the Y-succinate MOF, allowing Cd(II) to occupy more sites [203]. Gerard et al. [140] studied the adsorption capacities of UiO-66, UiO-66-(SH)2), CeO2@UiO-66 and CeO2@UiO-66-(SH)2 for the removal of Cd(II) ions from the water, and the removal efficiencies reported were 2%, 97%, 0%, and 91%, respectively [140]. Mahmoud et al. [143] prepared nFe3O4@MIL-88A(Fe)/APTMS for the adsorption of Cd(II) ions, and the maximum adsorption capacity was 693 mg/g. Interaction of nFe3O4@- MIL-88A(Fe)/APTMS with the cationic species of Cd(II) might be accomplished by coordination bonds at pH > 4, because the adsorbent surface charge is negative at pH> 4 [143]. In addition, Liu et al. [204] studied UiO-66, UiO-66@mSi-SH, and UiO-66@mSi-SO3H for the adsorption of Cd(II) ions from water. The maximum adsorption capacities of UiO-66@mSi-SO3H, UiO-66, and UiO-66@mSi-SH were 410, 112, and 212 mg/g, respectively. The su- perior adsorption performance of UiO-66@mSi-SO3H is because three oxygen atoms in -SO3H can coordinate with metal ions from different directions to form two-dimensional and three-dimensional spatial structures with more coordination modes [204]. Ahmadijokani et al. [145] prepared an UiO-66-EDA for the removal of Cd(II) ions from water. The maximum adsorption capacity was estimated to be 217 mg/g. The adsorption of Cd(II) ions by UiO-66-EDA is dependent on electron exchange, covalent, and electrostatic interactions between the metal ions and functional groups on the UiO-66-EDA surface [145]. Among the studied MOFs for cadmium adsorption (Table 6), the ZIF- 8-mmen, which is synthesized through the simple method of modification of ZIF-8 by dimethylethylenediamine, has the highest ab- sorption value at pH= 6, because at this pH surface protonation and positive charges density become weaker and the electrostatic attraction forces cause the higher cadmium removal. Besides, this high efficacy is achieved at a near-neutral pH, which might be favorable for natural water or wastewater treatment. 5.3.6. Boron Boron is primarily present in the form of oxygenates, and its principal forms in nature is borax and borax ores, which are widely found in seawater and salt lakes [205]. A guideline value of 2

Journal of Environmental Chemical Engineering 10 (2022) 107394 14coordination sites and the loading of active species on MOFs are effec- tive in the interaction of heavy metal ions and MOFs. Also, in addition to guest-host interactions, acid-base interactions, and hydrogen bonds, coordination with metal sites also plays an effective role in adsorption. An overarching comparison between the different MOFs synthesized for the adsorption of heavy metals of Pb, Hg, As, Cr, Cd, and B ions showed overall that MOFs can adsorb heavy metal at the pH range of ca. 2–7. The maximum efficiency among the reviewed MOFs in this work for the adsorption of Pb, Hg, As, Cr, Cd, and B ions are 12, 11, 104, 51, 15, and 0.32 mg/m2, respectively. The maximum time required to reach equilibrium in MOFs applied to absorb Pb, Hg, As, Cr, Cd, and B ions are 960, 360, 720, 1400, 360, and 720 min, respectively. The maximum absorption capacity of Pb, Hg, As, Cr, Cd, and B ions among the MOFs evaluated in this study are 1600, 1634, 552, 1092, 1000, and 579 mg/g, respectively (Fig. 5). Table 8 provides the advantages and disadvantages of MOFs. Although MOFs have several advantages and make a very exciting ma- terial for effective adsorption, there are significant drawbacks involved in their application. Most MOFs are prepared by solvothermal methods that use a large number of organic solvents such as methanol and N, N- dimethylformamide (DMF). The effect of the solvents used on the environment must be carefully considered and when possible, to be replaced by a “greener” alternative. We suggest that the negative effects of organic matter may be minimized by recycling solvents, compatible with the framework of circular economy and reuse of resources. Effec- tively, the synthesis of MOFs using water solvent [214] or solvent-free [215] conditions is progressing, but still needs further improvement. Also, some MOFs have low stability under acid and/or base condi- tions. To overcome this problem, it is necessary to use more appropriate base for MOFs synthesis. Many MOFs are reported to have fine pores that may interfere with the mobility of large metal ions. Accordingly, re- searchers in future studies are likely to modify the structures of the MOFs for full use of adsorption sites. Finally, the adsorbent price is an important factor in its application and industrial production. At present, almost all MOFs are still in the experimental stage and have not reached the commercial phase, because they cost much more than other adsor- bents such as clay and zeolites. Partially, this is due to the high price of organic linkers used in MOFs production, leading to the high final cost of MOFs. 6.2. Comparison of MOFs with other adsorbents Despite their obvious issues yet to be overcome, the results so far encourage further development and discovery of materials, especially considering the impressive adsorptive performance of MOFs over other materials. For the adsorption of heavy metals from wastewater, various adsorbents such as astragalus, CNTs, ACs, many bio-sorbents, activated alumina, titanium dioxide, fly ash bottom ash, activated red mud, modified lawny grass, ash gourd peel powder, peanut shell, sulfonated biochar, cassava peels and chitosan resin have been reported in the literature (Table 9). Compared to different adsorbents, MOFs have interesting features, such as multiple times higher number and size of pores open metal sites, etc. Besides, MOFs structures are more flexible for custom design; the diversity of pore size allows MOFs to adsorb a wide range of contaminants and making them valuable in various research fields, such as adsorption. For example, Table 9 shows that the maximum capacity of TMU-32 for the adsorption of Pb(II) and Hg(II) is 909 and 476 mg/g, respectively that is much higher than other adsor- bents. Also, the efficacy factor of this MOF for the absorption of Pb(II) and Hg(II) is 2.1 and 1.1 mg/m2, respectively, which is a very high amount compared to other materials given in Table 9. 7. Conclusions Adsorption is an increasingly accepted method for the removal of heavy metals from aqueous solutions due to its easy operation, envi- ronmentally friendly nature, and low cost. Accordingly, the develop- ment of economical, efficient, and green adsorbents for the removal of heavy metals in necessary. Among the adsorbents, MOFs and MOF-based composites constitute a novel and promising group of materials that indicated excellent ability for adsorbing heavy metals from aqueous media. In this review, we focused on the presentation on the advances made in the development of various MOFs for the adsorption of toxic heavy metals, including Pb, Hg, As, Cr, Cd, and B, offering an in-depth assessment and a better understanding of MOFs for the adsorption of heavy metal ions. MOFs were shown to be superior to other porous materials, due toMaximum adsorp�on of heavy metals Pb pH= 7 T=20 min q=1600 mg/g [141] Hg pH=7 T=1 min q=1634 mg/g [133] As

Journal of Environmental Chemical Engineering 10 (2022) 107394 15their tunable porosities, higher surface area, and better functionality, which collectively lead to significantly better performance. To explain this remarkable behavior, several adsorption mechanisms are proposed in the literature, including the coordination between heavy metals with the open metal sites of MOFs, acid-base interactions, electrostatic in- teractions, and hydrogen bonding. We explored the interactions and the characteristics of various MOFs and we are now one step closer to elucidating the mechanisms of these new classes of materials and their efficacy against heavy metals removal. It is the author’s conviction that MOFs will dominate the field of adsorption, as they already outperform the other adsorbents in metals removal, efficacy, functionality, range of application, etc. 8. Outlook and future perspectives Despite all the advantages and the promising potential that MOFs present, this technology is far from perfect yet. There are still major challenges before using MOF in the water treatment practice, such as the challenging synthesis methods, the stability issues and the tuning of pore size. Apart from their physicochemical aspects, therefore, the search for other low-cost alternatives for the costliest reagents (i.e., organic linkers) should be considered as a field for further research. In sum, MOFs, as a material for the adsorption of heavy metals from the contaminated water has a great outlook for the near future. How- ever, in order to eliminate heavy metal contamination by MOFs and MOF-based adsorbents in a manner that remains competitive to other cheap or greener alternatives, future studies should extend their appli- cation potentials, through: 1) the development of green MOFs with modified surface characters (e. g., high porosity and active sites); 2) synthesis of multicomponent MOFs with functional composites such as semiconductors, carbon-based materials, quantum dots, and ionic liquids; 3) preparing novel and multifunctional MOFs such as defect-tunable MOFs, MOF-on-MOF hetero-architectures and non-crystalline MOFs. 4) developing the magnetized MOFs for facilitating the separation of the adsorbent after the treatment. Credit authorship contribution statement Nasrin Abdollahi: Investigation, Writing – original draft, Writing – review & editing, Visualization. Gholamreza Moussavi: Conceptuali- zation, Methodology, Validation, Visualization, Resources, Writing – original draft, Writing – review & editing, Supervision, Funding acqui- sition. Stefanos Giannakis: Methodology, Validation, Visualization, Writing – original draft, Writing – review & editing, Funding acquisition. Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper. Acknowledgements This work was technically and financially supported by the Tarbiat Modares University, Iran, under the Research Group grant No. IG39801. Nasrin Abdullahi thanks the Iran Science Elite Federation, ISEF, for the financial support during her Postdoctoral position in Tarbiat Modares University, Iran. Stefanos Giannakis would like to acknowledge the Spanish Ministry of Science, Innovation and Universities (MICIU) for the Ram´on y Cajal Fellowship (RYC2018-0233-I). References [1] N. Johnson, R. Carmen, E. Jaime, Managing water for people and nature, Science 292 (5519) (2001) 1071–1072, https://doi.org/10.1126/science.1058821. [2] C.J. V¨or¨osmarty, P. Green, J. Salisbury, R.B. Lammers, Global water resources: vulnerability from climate change and population growth, Science 289 (5477) (2000) 284–288, https://doi.org/10.1126/science.289.5477.284. [3] A. Rolston, Social changes affect water quality too, Nature 536 (7617) (2016) 396-396, https://doi.org/10.1038/536396b. Table 9 Comparative evaluation of various adsorbents investigated for heavy metals removal. Adsorbent Ion Adsorbent (g/L) Temperature (◦C) Adsorption capacity (mg/g) Efficacy factor (mg/m2) Ref. MOF (TMU-32) Pb(II), Hg(II) Very Low Ambient Very High Very High 0.005 25 909, 476 2.1, 1.1 [134] Astragalus Cu(II) Low Ambient Low – 0.55 25 2 - [37] MWCNTs Cu(II), Pb(II) Very Low Ambient High – 0.03 25 143, 200 - [38] Activated carbon Cd(II), Pb(II) Low Ambient Moderate Low 0.2 25 61, 90 0.08, 0.11 [39] Fly Ash Cd(II) High Ambient High – 2 25 142 - [216] Zeolite H-MFI-24 As(V) High Ambient Moderate Very Low 2 20 36 0.08 [129] Activated Red Mud Pb(II) High High Low – 4 30 6 - [217] Activated alumina As(III) Very High Ambient Very Low Very Low 1–13 25 0.2 < 0.01 [113] Modified Lawny Grass Pb(II) Very Low High High – 0.5 29 137 - [218] Ash Gourd Peel Powder Cr(VI) High High Low – 6 28 19 - [219] Peanut Shell Cr(VI) High High Low – 1 30 4 - [220] Titanium dioxide As(III), As(V) High Low Moderate Low 1 13 32, 41 0.13, 0.16 [135] Cassava peels Pb(II) High Very High Low – 10 39-85 6 - [

Journal of Environmental Chemical Engineering 10 (2022) 107394 16[4] P. Kumar, V. Bansal, K.H. Kim, E.E. Kwon, Metal-organic frameworks (MOFs) as futuristic options for wastewater treatment, J. Ind. Eng. Chem. 62 (2018) 130–145, https://doi.org/10.1016/j.jiec.2017.12.051. [5] A. Mark, Science and technology for water purification in the coming decades, Nature 452 (2008) 301–310, https://doi.org/10.1038/nature06599. [6] M.A. Shannon, P.W. Bohn, M. Elimelech, J.G. Georgiadis, B.J. Marinas, A. M. Mayes, Science and technology for water purification in the coming decades, Nanosci. Technol. 452 (2010) 337–346, https://doi.org/10.1142/ 9789814287005_0035. [7] F. Yang, I.Y. Massey, Exposure routes and health effects of heavy metals on children, Biometals 32 (4) (2019) 563–573, https://doi.org/10.1007/s10534- 019-00193-5. [8] N. Herawati, S. Suzuki, K. Hayashi, I.F. Rivai, H. Koyama, Cadmium, copper, and zinc levels in rice and soil of Japan, Indonesia, and China by soil type, Bull. Environ. Contam. Toxicol. 64 (1) (2000) 33–39, https://doi.org/10.1007/ s001289910006. [9] L. Rani, J. Kaushal, A.L. Srivastav, P. Mahajan, A critical review on recent developments in MOF adsorbents for the elimination of toxic heavy metals from aqueous solutions, Environ. Sci. Pollut. Res. 27 (2020) 44771–44796, https://doi. org/10.1007/s11356-020-10738-8. [10] W. Salomons, U. F¨orstner, P. Mader, Heavy Metals: Problems and Solutions, Springer. Verlag.,, 1994, pp. 1–414, https://doi.org/10.1007/978-3-642-79316- 5. [11] A.V. Hirner, H. Emons, Organic Metal and Metalloid Species in the Environment: Analysis, Distribution, Processes and Toxicological Evaluation, Springer. Sci, 2004, pp. 1–328, https://doi.org/10.1007/978-3-662-09135-7. [12] Z. Fu, X. Shuhua, The effects of heavy metals on human metabolism, Toxicol. Mech. Methods 30 (3) (2020) 167–176, https://doi.org/10.1080/ 15376516.2019.1701594. [13] F. Fu, Q. Wang, Removal of heavy metal ions from wastewaters: a review, J. Environ. Manag. 92 (3) (2011) 407–418, https://doi.org/10.1016/j. jenvman.2010.11.011. [14] Y. Zhang, X. Duan, Chemical precipitation of heavy metals from wastewater by using the synthetical magnesium hydroxy carbonate, Water Sci. Technol. 81 (6) (2020) 1130–1136, https://doi.org/10.2166/wst.2020.208. [15] J. Charles, C. Bradu, N. Morin-Crini, B. Sancey, P. Winterton, G. Torri, G. Crini, Pollutant removal from industrial discharge water using individual and combined effects of adsorption and ion-exchange processes: chemical abatement, J. Saudi Chem. Soc. 20 (2) (2016) 185–194, https://doi.org/10.1016/j.jscs.2013.03.007. [16] A. Lalmi, K.E. Bouhidel, B. Sahraoui, C. Houda Anfif, Removal of lead from polluted waters using ion exchange resin with Ca(NO3)2 for elution, Hydrometallurgy 178 (2018) 287–293, https://doi.org/10.1016/j. hydromet.2018.05.009. [17] N.R. Nicomel, K. Leus, K. Folens, P. Van Der Voort, G. Du Laing, Technologies for arsenic removal from water: current status and future perspectives, Int. J. Environ. Res. Public. Health 13 (1) (2016) 62, https://doi.org/10.3390/ ijerph13010062. [18] D.C. Sherrington, Preparation, structure and morphology of polymer supports, Chem. Comm. 21 (1998) 2275–2286, https://doi.org/10.1039/A803757D. [19] K.A. Kun, R. Kunin, The pore structure of macroreticular ion exchange resins, J. Polym. Sci. C. Polym. Symp. 16 (3) (1967) 1457–1469, https://doi.org/ 10.1002/polc.5070160323. [20] G. Al-Enezi, M.F. Hamoda, N. Fawzi, Ion exchange extraction of heavy metals from wastewater sludges, J. Environ. Sci. Health Part. A. 39 (2) (2004) 455–464, https://doi.org/10.1081/ese-120027536. [21] A. Da̧ browski, Z. Hubicki, P. Podko´scielny, E. Robens, Selective removal of the heavy metal ions from waters and industrial wastewaters by ion-exchange method, Chemosphere 56 (2) (2004) 91–106, https://doi.org/10.1016/j. chemosphere.2004.03.006. [22] P.A. Brown, S.A. Gill, S.J. Allen, Metal removal from wastewater using peat, Water Res. 34 (16) (2000) 3907–3916, https://doi.org/10.1016/S0043-1354(00) 00152-4. [23] A. Pohl, Removal of heavy metal ions from water and wastewaters by sulfur- containing precipitation agents, Water Air. Soil. Pollut. 231 (10) (2020) 1–17, https://doi.org/10.1007/s11270-020-04863-w. [24] G. Behboody, Methods for removing heavy metals from water and wastewater: a review study, J. Environ. Health Res 6 (2) (2020), https://doi.org/10.22038/ JREH.2020.46594.1352. [25] B. Ozyurt, S. Camcioglu, M. Firtin, C. Ates, H. Hapoglu, W. Treatment, Boron removal from industrial wastewaters by means of optimized sequential chemical precipitation and coagulation processes, Desalin. Water Treat. 172 (2019) 292–300, https://doi.org/10.5004/dwt.2019.24932. [26] M. Ince, O.K. Ince, Heavy metal removal techniques using response surface methodology: water/wastewater treatment, Biochem. Toxicol. Heavy Met. Nanomater. IntechOpen (2019) 1–19, https://doi.org/10.5772/ intechopen.88915. [27] A. Pohl, Removal of heavy metal ions from water and wastew

Journal of Environmental Chemical Engineering 10 (2022) 107394 17[55] S.D. Fost, M.O. Aly, Adsorption Processes for Water Treatment, Betterworth Publications, Stoneharm. Massachusetts. Mass. USA., 1981, pp. 25–64, https:// doi.org/10.1016/B978-0-409-90000-2.50005-4. [56] T.L. Hill, Statistical mechanics of multimolecular adsorption II. Localized and mobile adsorption and absorption, J. Chem. Phys. 14 (7) (1946) 441–453, https://doi.org/10.1063/1.1724166. [57] P. Sampranpiboon, P. Charnkeitkong, X. Feng, Equilibrium isotherm models for adsorption of zinc(II) ion from aqueous solution on pulp waste, WSEAS Trans. Environ. Dev. 10 (2014) 35–47. [58] K. Vijayaraghavan, T. Padmesh V.,N., K. Palanivelu, M. Velan, Biosorption of nickel (II) ions onto Sargassum wightii: application of two-parameter and three- parameter isotherm models, J. Hazard. Mater. 133 (1–3) (2006) 304–308, https://doi.org/10.1016/j.jhazmat.2005.10.016. [59] O. Celebi, C. Üzüm, T. Shahwan, H.N. Erten, A radiotracer study of the adsorption behavior of aqueous Ba2+ ions on nanoparticles of zero-valent iron, J. Hazard. Mater. 148 (3) (2007) 761–767, https://doi.org/10.1016/j.jhazmat.2007.06.122. [60] M.T. Amin, A.A. Alazba, M. Shafiq, Adsorptive removal of reactive black 5 from wastewater using bentonite clay: isotherms, kinetics and thermodynamics, Sustainability 7 (11) (2015) 15302–15318, https://doi.org/10.3390/ su71115302. [61] R. Farouq, N.S. Yousef, Equilibrium and kinetics studies of adsorption of copper (II) ions on natural biosorbent, Int. J. Chem. Eng. Appl. 6 (5) (2015) 319, https:// doi.org/10.7763/IJCEA.2015.V6.503. [62] H.R. Fowler , E.A. Guggenheim , Statistical thermodynamics of super-lattices Proc. Math. Phys. Eng. Sci. P R. SOC A-Math. Phy. 174 957 1940 189 206 doi: 10.1098/rspa.1940.0014. [63] K.Y. Foo, B.H. Hameed, Insights into the modeling of adsorption isotherm systems, Chem. Eng. J. 156 (1) (2010) 2–10, https://doi.org/10.1016/j. cej.2009.09.013. [64] I. Qui˜nones, G. Guiochon, Derivation and application of a Jovanovic–Freundlich isotherm model for single-component adsorption on heterogeneous surfaces, J. Colloid Interf. Sci. 183 (1) (1996) 57–67, https://doi.org/10.1006/ jcis.1996.0518. [65] M. Gubernak, W. Zapala, K. Kaczmarski, Analysis of amylbenzene adsorption equilibria on an RP-18e chromatographic column, Acta Chromatogr. 13 (2003) 38–59. [66] T.W. Weber, R.K. Chakravorti, Pore and solid diffusion models for fixed-bed adsorbers, AIChE. J. 20 (2) (1974) 228–238, https://doi.org/10.1002/ aic.690200204. [67] M. Davoudinejad, S.A. Ghorbanian, Modeling of adsorption isotherm of benzoic compounds onto GAC and introducing three new isotherm models using new concept of Adsorption Effective Surface (AES), Sci. Res. Essays 8 (46) (2013) 2263–2275, https://doi.org/10.5897/SRE10.643. [68] G.P. Jeppu, T.P. Clement, A modified Langmuir-Freundlich isotherm model for simulating pH-dependent adsorption effects, J. Contam. Hydrol. 129 (2012) 46–53, https://doi.org/10.1016/j.jconhyd.2011.12.001. [69] T.J. Behbahani, Z.J. Behbahani, A new study on asphaltene adsorption in porous media, Pet. Coal 56 (5) (2014) 459–466, https://doi.org/708-986-807-077. [70] A.R. Khan, R. Ataullah, A. Al-Haddad, Equilibrium adsorption studies of some aromatic pollutants from dilute aqueous solutions on activated carbon at different temperatures, J. Colloid Interf. Sci. 194 (1) (1997) 154–165, https://doi.org/ 10.1006/jcis.1997.5041. [71] O. Amrhar, H. Nassali, M.S. Elyoubi, Application of nonlinear regression analysis to select the optimum absorption isotherm for methylene blue adsorption onto natural illitic clay, Bull. Soc. R. Sci. Liege 84 (2015) 116–130. 〈https://popups. uliege.be/0037-9565/index.php?id=4865〉. [72] B. Subramanyam, D. Ashutosh, Adsorption isotherm modeling of phenol onto natural soils–applicability of various isotherm models, Int. J. Environ. Res 6 (1) (2012) 265–276, https://doi.org/10.22059/IJER.2011.492. [73] M.F. Dilekoglu, Use of genetic algorithm optimization technique in the adsorption of phenol on banana and grapefruit peels, J. Chem. Soc. Pak. 38 (6) (2016) 1252–1262. [74] Z.L. Yaneva, B.K. Koumanova, N.V. Georgieva, Linear and nonlinear regression methods for equilibrium modelling of p-nitrophenol biosorption by Rhizopus oryzae: comparison of error analysis criteria, J. Chem. 2013 (2013) 1–10, https:// doi.org/10.1155/2013/517631. [75] G. McKay, A. Mesdaghinia, S. Nasseri, M. Hadi, M.S. Aminabad, Optimum isotherms of dyes sorption by activated carbon: fractional theoretical capacity & error analysis, Chem. Eng. J. 251 (2014) 236–247, https://doi.org/10.1016/j. cej.2014.04.054. [76] K. Vijayaraghavan, Biosorption of lanthanide (praseodymium) using Ulva lactuca: mechanistic study and application of two, three, four and five parameter isotherm models, J. Environ. Biotechnol. Res. 1 (1) (2015) 10–17. [77] N. Sivarajasekar, R. Baskar, Adsorption of basic red 9 onto activated carbon derived from immature cotton seeds: isotherm studi

Journal of Environmental Chemical Engineering 10 (2022) 107394 18[104] J. Canivet, A. Fateeva, Y. Guo, B. Coasne, D. Farrusseng, Water adsorption in MOFs: fundamentals and applications, Chem. Soc. Rev. 43 (2014) 5594–5617, https://doi.org/10.1039/C4CS00078A. [105] N.C. Burtch, H. Jasuja, K.S. Walton, Water stability and adsorption in metal–organic frameworks, Chem. Rev. 114 (20) (2014) 10575–10612, https:// doi.org/10.1021/cr5002589. [106] I.V. Babich, J.A. Moulijn, Science and technology of novel processes for deep desulfurization of oil refinery streams: a review, Fuel 82 (6) (2003) 607–631, https://doi.org/10.1016/S0016-2361(02)00324-1. [107] J. Liu, P.K. Thallapally, B.P. McGrail, D.R. Brown, J. Liu, Progress in adsorption- based CO2 capture by metal–organic frameworks, Chem. Soc. Rev. 41 (6) (2012) 2308–2322, https://doi.org/10.1039/C1CS15221A. [108] M. Seredych, T.J. Bandosz, Removal of dibenzothiophenes from model diesel fuel on sulfur rich activated carbons, Appl. Catal. B Environ. 106 (1–2) (2011) 133–141, https://doi.org/10.1016/j.apcatb.2011.05.016. [109] T.G. Glover, G.W. Peterson, B.J. Schindler, D. Britt, O. Yaghi, MOF-74 building unit has a direct impact on toxic gas adsorption, Chem. Eng. Sci. 66 (2) (2011) 163–170, https://doi.org/10.1016/j.ces.2010.10.002. [110] S.H. Huo, X.P. Yan, Metal–organic framework MIL-100 (Fe) for the adsorption of malachite green from aqueous solution, J. Mater. Chem. 22 (15) (2012) 7449–7455, https://doi.org/10.1039/C2JM16513A. [111] N.A. Khan, S.H. Jhung, Adsorptive removal of benzothiophene using porous copper-benzenetricarboxylate loaded with phosphotungstic acid, Fuel. Process. Technol. 100 (2012) 49–54, https://doi.org/10.1016/j.fuproc.2012.03.006. [112] N.A. Khan, S.H. Jhung, Low-temperature loading of Cu+ species over porous metal-organic frameworks (MOFs) and adsorptive desulfurization with Cu+- loaded MOFs, J. Hazard. Mater. 237 (2012) 180–185, https://doi.org/10.1016/j. jhazmat.2012.08.025. [113] K. Müller-Buschbaum, Y. Mokaddem, C.J. H¨oller, On an Unexpected 2D-linked Rare Earth 1, 2, 4–Triazolate Network: Synthesis, Crystal Structure, Spectroscopic and Thermal Properties of 2∞[Ho(Tz)3(TzH)2]TzH, Z. Anorg. Allg. Chem. 634 (15) (2008) 2973–2977, https://doi.org/10.1002/zaac.200800323. [114] M. Eddaoudi, H. Li, O.M. Yaghi, Highly porous and stable metal organic frameworks: structure design and sorption properties, J. Am. Chem. Soc. 122 (7) (2000) 1391–1397, https://doi.org/10.1021/ja9933386. [115] J.W. Yoon, H. Chang, S.J. Lee, Y.K. Hwang, D.Y. Hong, S.K. Lee, J.S. Chang, Selective nitrogen capture by porous hybrid materials containing accessible transition metal ion sites, Nat. Mater. 16 (5) (2017) 526–531, https://doi.org/ 10.1038/nmat4825. [116] W. Yu, M. Luo, Y. Yang, H. Wu, W. Huang, K. Zeng, F. Luo, Metal-organic framework (MOF) showing both ultrahigh As (V) and As (III) removal from aqueous solution, J. Solid. State Chem. 269 (2019) 264–270, https://doi.org/ 10.1016/j.jssc.2018.09.042. [117] M. Moradi, Mercuric chloride adsorption on sulfur-containing BC2N nanotube: toward HSAB concept, J. Struct. Chem. 25 (4) (2014) 1091–1097, https://doi. org/10.1007/s11224-013-0387-x. [118] E. Tahmasebi, M.Y. Masoomi, Y. Yamini, A. Morsali, Application of mechanosynthesized azine-decorated zinc (II) metal–organic frameworks for highly efficient removal and extraction of some heavy-metal ions from aqueous samples: a comparative study, Inorg. Chem. 54 (2) (2015) 425–433, https://doi. org/10.1021/ic5015384. [119] F. Ke, L.G. Qiu, Y.P. Yuan, F.M. Peng, X. Jiang, A.J. Xie, J.F. Zhu, Thiol- functionalization of metal-organic framework by a facile coordination-based postsynthetic strategy and enhanced removal of Hg2+ from water, J. Hazard. Mater. 196 (2011) 36–43, https://doi.org/10.1016/j.jhazmat.2011.08.069. [120] E. Tahmasebi, M.Y. Masoomi, Y. Yamini, A. Morsali, Application of mechanosynthesized azine-decorated zinc (II) metal–organic frameworks for highly efficient removal and extraction of some heavy-metal ions from aqueous samples: a comparative study, Inorg. Chem. 54 (2) (2015) 425–433, https://doi. org/10.1021/ic5015384. [121] N.K. Amin, Removal of direct blue-106 dye from aqueous solution using new activated carbons developed from pomegranate peel: adsorption equilibrium and kinetics, J. Hazard. Mater. 165 (1–3) (2009) 52–62, https://doi.org/10.1016/j. jhazmat.2008.09.067. [122] J. Zhang, Z. Xiong, C. Li, C. Wu, Exploring a thiol-functionalized MOF for elimination of lead and cadmium from aqueous solution, J. Mol. Liq. 221 (2016) 43–50, https://doi.org/10.1016/j.molliq.2016.05.054. [123] J. Li, Y.N. Wu, Z. Li, M. Zhu, F. Li, Characteristics of arsenate removal from water by metal-organic frameworks (MOFs), Water Sci. Technol. 70 (8) (2014) 1391–1397, https://doi.org/10.2166/wst.2014.390. [124] O. Tarrago, M.J. Brown, Case studies in environmental medicine (CSEM) lead toxicity, Agency Toxic. Subst. Dis. Regist. )2017(1–185 . [125] S. Tunali, T. Akar, A.S. ¨

Journal of Environmental Chemical Engineering 10 (2022) 107394 19aqueous solution, Ceram. Int. 45 (12) (2019) 15720–15724, https://doi.org/ 10.1016/j.ceramint.2019.04.246. [152] P. Yang, Y. Shu, Q. Zhuang, Y. Li, J. Gu, A robust MOF-based trap with high- density active alkyl thiol for the super-efficient capture of mercury, Chem. Commun. 55 (86) (2019) 12972–12975, https://doi.org/10.1039/C9CC06255F. [153] Z.S. Hasankola, R. Rahimi, H. Shayegan, E. Moradi, V. Safarifard, Removal of Hg2 + heavy metal ion using a highly stable mesoporous porphyrinic zirconium metal- organic framework, Inorg. Chim. Acta 501 (2020), 119264, https://doi.org/ 10.1016/j.ica.2019.119264. [154] V.K. Sharma, M. Sohn, Aquatic arsenic: toxicity, speciation, transformations, and remediation, Environ. Int. 35 (4) (2009) 743–759, https://doi.org/10.1016/j. envint.2009.01.005. [155] Y. Dong, J. Li, J. Zan, Occurrence and distribution of arsenic in water and soil at inland-arid/semi-arid basin, IOP Conf. Ser. Earth. Environ. Sci. 146 (1) (2018), 012052, https://doi.org/10.1088/1755-1315/146/1/012052. [156] K. Folens, K. Leus, N.R. Nicomel, M. Meledina, S. Turner, G. Van Tendeloo, P. Van Der Voort, Fe3O4@ MIL-101–a selective and regenerable adsorbent for the removal of as species from water, Eur. J. Inorg. Chem. 2016 (27) (2016) 4395–4401, https://doi.org/10.1002/ejic.201600160. [157] J. Cai, X. Wang, Y. Zhou, L. Jiang, C. Wang, Selective adsorption of arsenate and the reversible structure transformation of the mesoporous metal–organic framework MIL-100 (Fe), Phys. Chem. Chem. Phys. 18 (16) (2016) 10864–10867, https://doi.org/10.1039/C6CP00249H. [158] B.J. Abu Tarboush, A. Chouman, A. Jonderian, M. Ahmad, M. Hmadeh, M. Al- Ghoul, Metal–organic framework-74 for ultratrace arsenic removal from water: experimental and density functional theory studies, ACS Appl. Nano. Mater. 1 (7) (2018) 3283–3292, https://doi.org/10.1021/acsanm.8b00501. [159] H. Atallah, M.E. Mahmoud, A. Jelle, A. Lough, M. Hmadeh, A highly stable indium based metal organic framework for efficient arsenic removal from water, Dalton. Trans. 47 (3) (2018) 799–806, https://doi.org/10.1039/C7DT03705H. [160] T. Chowdhury, L. Zhang, J. Zhang, S. Aggarwal, Removal of arsenic (III) from aqueous solution using metal organic framework-graphene oxide nanocomposite, Nanomaterials 8 (12) (2018) 1062, https://doi.org/10.3390/nano8121062.. [161] H. Wu, M.D. Ma, W.Z. Gai, H. Yang, J.G. Zhou, Z. Cheng, Z.Y. Deng, Arsenic removal from water by metal-organic framework MIL-88A microrods, Environ. Sci. Pollut. Res. 25 (27) (2018) 27196–27202, https://doi.org/10.1007/s11356- 018-2751-2. [162] J.B. Huo, L. Xu, J.C.E. Yang, H.J. Cui, B. Yuan, M.L. Fu, Magnetic responsive Fe3O4-ZIF-8 core-shell composites for efficient removal of As (III) from water, Colloids Surf. A Physicochem. Eng. Asp. 539 (2018) 59–68, https://doi.org/ 10.1016/j.colsurfa.2017.12.010. [163] S.M. Prabhu, S. Imamura, K. Sasaki, Mono-, di-, and tricarboxylic acid facilitated lanthanum-based organic frameworks: insights into the structural stability and mechanistic approach for superior adsorption of arsenate from water, ACS Sustain. Chem. Eng. 7 (7) (2019) 6917–6928, https://doi.org/10.1021/ acssuschemeng.8b06489. [164] J. Sun, X. Zhang, A. Zhang, C. Liao, Preparation of Fe–Co based MOF-74 and its effective adsorption of arsenic from aqueous solution, J. Environ. Sci. 80 (2019) 197–207, https://doi.org/10.1016/j.jes.2018.12.013. [165] W. Yu, M. Luo, Y. Yang, H. Wu, W. Huang, K. Zeng, F. Luo, Metal-organic framework (MOF) showing both ultrahigh As (V) and As (III) removal from aqueous solution, J. Solid. State Chem. 269 (2019) 264–270, https://doi.org/ 10.1016/j.jssc.2018.09.042. [166] J.B. Huo, L. Xu, X. Chen, Y. Zhang, J.C.E. Yang, B. Yuan, M.L. Fu, Direct epitaxial synthesis of magnetic Fe3O4@UiO-66 composite for efficient removal of arsenate from water, Micro Mesopor. Mat. 276 (2019) 68–75, https://doi.org/10.1016/j. micromeso.2018.09.017.. [167] P. Qi, R. Luo, T. Pichler, J. Zeng, Y. Wang, Y. Fan, K. Sui, Development of a magnetic core-shell Fe3O4@TA@UiO-66 microsphere for removal of arsenic (III) and antimony (III) from aqueous solution, J. Hazard. Mater. 378 (2019), 120721, https://doi.org/10.1016/j.jhazmat.2019.05.114. [168] Y. Gu, D. Xie, Y. Wang, W. Qin, H. Zhang, G. Wang, H. Zhao, Facile fabrication of composition-tunable Fe/Mg bimetal-organic frameworks for exceptional arsenate removal, Chem. Eng. J. 357 (2019) 579–588, https://doi.org/10.1016/j. cej.2018.09.174.. [169] X. Zheng, M. Yi, Z. Chen, Z. Zhang, L. Ye, G. Cheng, Y. Xiao, Efficient removal of As (V) from simulated arsenic-contaminated wastewater via a novel metal–organic framework material: Synthesis, structure, and response surface methodology, Appl. Organomet. Chem. 34 (5) (2020) 1–11, https://doi.org/ 10.1002/aoc.5584. [170] R. Xu, Q. Ji, P. Zhao, M. Jian, C. Xiang, C. Hu, J. Qu, Hierarchically porous UiO- 66 with tunable mesopores and oxygen vacancies for enha

Journal of Environmental Chemical Engineering 10 (2022) 107394 20[197] C. Liu, P. Wang, X. Liu, X. Yi, D. Liu, Z. Zhou, Ultrafast removal of cadmium (II) by green cyclodextrin metal–organic-framework-based nanoporous carbon: adsorption mechanism and application, Chem. Asian J. 14 (2) (2019) 261–268, https://doi.org/10.1002/asia.201801431. [198] P. Nasehi, B. Mahmoudi, S.F. Abbaspour, M.S. Moghaddam, Cadmium adsorption using novel MnFe2O4TiO2-UIO-66 magnetic nanoparticles and condition optimization using a response surface methodology, RSC Adv. 9 (35) (2019) 20087–20099, https://doi.org/10.1039/C9RA03430G. [199] A.S. Yusuff, L.T. Popoola, E.O. Babatunde, Adsorption of cadmium ion from aqueous solutions by copper-based metal organic framework: equilibrium modeling and kinetic studies, Appl. Water Sci. 9 (4) (2019) 1–11, https://doi.org/ 10.1007/s13201-019-0991-z. [200] E. Binaeian, S. Maleki, N. Motaghedi, M. Arjmandi, Study on the performance of Cd2+ sorption using dimethylethylenediamine-modified zinc-based MOF (ZIF-8- mmen): optimization of the process by RSM technique, Sep. Sci. Technol. 55 (15) (2020) 2713–2728, https://doi.org/10.1080/01496395.2019.1655056. [201] W.A. El-Yazeed, Y.G. Abou El-Reash, L.A. Elatwy, A.I. Ahmed, Novel bimetallic Ag-Fe MOF for exceptional Cd and Cu removal and 3, 4-dihydropyrimidinone synthesis, J. Taiwan. Inst. Chem. Eng. 114 (2020) 199–210, https://doi.org/ 10.1016/j.jtice.2020.09.028. [202] F.A. Elaiwi, A. Sirkecioglu, Amine-functionalized metal organic frameworks MIL- 101 (Cr) adsorbent for copper and cadmium ions in single and binary solution, Sep. Sci. Technol. 55 (18) (2020) 3362–3374, https://doi.org/10.1080/ 01496395.2019.1706571. [203] N. Fajrin, I.R. Saragi, Y.K. Krisnandi, A. Zulys, Synthesis of metal organic framework (MOF) using lanthanum and yttrium metals with succinate acid ligand as adsorbent for cadmium (II) metal ion, Aip. Conf. Proc. 2242 (1) (2020), 040021, https://doi.org/10.1063/5.0008318. [204] J. Liu, H. Cui, J. Li, M. Chen, A research on the cadmium ions adsorption of Sulfhydryl-and sulfo-functionalized UIO-66 with silica layer from water, J. Environ. Chem. Eng. 9 (1) (2021), 104621, https://doi.org/10.1016/j. jece.2020.104621. [205] M. Bodzek, The removal of boron from the aquatic environment–state of the art, Desalin. Water Treat. 57 (3) (2016) 1107–1131, https://doi.org/10.1080/ 19443994.2014.1002281. [206] J. Wolska, M. Bryjak, Methods for boron removal from aqueous solutions—a review, Desalin 310 (2013) 18–24, https://doi.org/10.1016/j.desal.2012.08.003. [207] J. Lyu, N. Zhang, H. Liu, Z. Zeng, J. Zhang, P. Bai, X. Guo, Adsorptive removal of boron by zeolitic imidazolate framework: kinetics, isotherms, thermodynamics, mechanism and recycling, Sep. Purif. Technol. 187 (2017) 67–75, https://doi. org/10.1016/j.seppur.2017.05.059. [208] J. Lyu, H. Liu, Z. Zeng, J. Zhang, Z. Xiao, P. Bai, X. Guo, Metal–organic framework UiO-66 as an efficient adsorbent for boron removal from aqueous solution, Ind. Eng. Chem. Res. 56 (9) (2017) 2565–2572, https://doi.org/10.1021/acs. iecr.6b04066. [209] J. Zhang, Y. Cai, K. Liu, Extremely effective boron removal from water by stable metal organic framework ZIF-67, Ind. Eng. Chem. Res. 58 (10) (2019) 4199–4207, https://doi.org/10.1021/acs.iecr.8b05656. [210] G. Hu, W. Zhang, Y. Chen, C. Xu, R. Liu, Z. Han, Removal of boron from water by GO/ZIF-67 hybrid material adsorption, Environ. Sci. Pollut. Res. 27 (22) (2020) 28396–28407, https://doi.org/10.1007/s11356-020-08018-6. [211] M. Jang, W. Chen, F.S. Cannon, Preloading hydrous ferric oxide into granular activated carbon for arsenic removal, Environ. Sci. Technol. 42 (9) (2008) 3369–3374, https://doi.org/10.1021/es7025399. [212] T.S. Singh, K.K. Pant, Equilibrium, kinetics and thermodynamic studies for adsorption of As (III) on activated alumina, Sep. Purif. Technol. 36 (2) (2004) 139–147, https://doi.org/10.1016/S1383-5866(03)00209-0. [213] A. Anjum, M. Datta, Removal of As(III) from aqueous solutions using montmorillonite, J. Anal. Sci. 2 (2012) 167–175, https://doi.org/10.4236/ jasmi.2012.23027. [214] K. Li, S. Lin, Y. Li, Q. Zhuang, J. Gu, Aqueous-phase synthesis of mesoporous Zr- Based MOFs templated by amphoteric surfactants, Angew. Chem. 130 (13) (2018) 3497–3501, https://doi.org/10.1002/ange.201800619. [215] C. Zou, S. Vagin, A. Kronast, B. Rieger, Template mediated and solvent-free route to a variety of UiO-66 metal–organic frameworks, RSC Adv. 6 (105) (2016) 102968–102971, https://doi.org/10.1039/C6RA23947A. [216] J.H. Park, J.H. Eom, S.L. Lee, S.W. Hwang, S.H. Kim, S.W. Kang, J.J. Yun, J. S. Cho, Y.H. Lee, D.C. Seo, Exploration of the potential capacity of fly ash and bottom ash derived from wood pelletbased thermal power plant for heavy metal removal, Sci. Total. Environ. 740 (2020), 140205, https://doi.org/10.1016/j. scitotenv.2020.140205. [217] M.K. Sahu, S. Mandal, S.S. Dash, P. Badhai, R.K. Patel, Removal of Pb(II) from aqueous solution by acid activated

Flipso