View Baby M1911A1 Assembly instructions(English version) flipbook.
Baby_M1911A1 Assembly instructions Hardware parts list Standard parts quantity Remarks spare parts Specifications Direct pin shaft 1x10 1 Diameter x Length(It is recommended to add spare parts) Direct pin shaft 2x8 1 Direct pin shaft 2x20 3 Direct pin shaft 2.5x8 1 Direct pin shaft 2.5x18 2 Direct pin shaft 3x20 1 Direct pin shaft 4x14 1 Flat head screw M2x10 2 Unlimited head types Countersunk head screw M2x8 1 Unlimited head types Countersunk head screw M2x4 1 Unlimited head types Countersunk head screw M2x18 1 Unlimited head types Flat head screw M2.5x5 4 Unlimited head types Spring 0.2x2.5x15 2 Wire diameter x round diameter x Length (material must be stainless steel) Spring 0.4x7x40 1 Spring 0.5x12x40 1 Re bore distance 22mm; It has the functions of sliding sleeve insurance and grip insurance; It can be decomposed by one key; The recommended diameter of launching rubber band ring is 4cm; Bomb capacity: 5
STEP1 Direct pin shaft 3X20 Push the pin shaft into the corresponding hole of "slide_stop", and universal glue can be used to ensure the overall stability STEP2 Use universal adhesive to bond the two parts in the figure. Please ensure stability and accurate positioning (pay attention to the installation direction)
STEP3 Flexi Locking Hardware parts required: Direct pin shaft 2.5X18; Direct pin shaft 2X8; Spring 0.2x2.5x15 1. Put the spring into the corresponding hole in the box 2/3 Ensure smooth rotation and sensitive trigger 4/5Install "hammer". Before grinding, ensure the total length 17.5mm (important). After installation, adjust the "hammer" bureau (the "hammer" and the pin are tightly matched, the pin and box of Kong Shisong, ensure the "hammer" rotation and lock normal). STEP4 Please fix the pin shaft with universal glue, and the exposed length is about 7.5mm After completion, grind the chamfering of the front end a of the barrel to ensure smoothness
STEP5 1. Ensure that it is stable without looseness, and the exposed length is about 3mm 2. Ensure that it is stable without looseness and can be fixed with universal glue STEP6.1 Pan head screw M2X10 Install the pan head screw m2x10 (Note: step 6.1 6.2 can not be carried out temporarily. In order to ensure the smooth fit between the chute and the frame chute, it shall be carried out after grinding and trimming)
STEP6.2 Install the spring and test the function after completion. If there is jamming, grind the chamfering of the interior and barrel seat to be smooth (Note: step 6.1 6.2 can not be carried out temporarily. In order to ensure the smooth fit between the chute and the frame chute, it shall be carried out after grinding and trimming) STEP7.1 (frame Split body) Install the 3 pins to (frame_middle) corresponding holes and complete the adjusting pin to ensure that the left and right sides protruding about 3.5mm
STEP7.2 (frame Split body) Install (frame_right) to ensure accurate positioning and correct shape matching. It can be bonded with universal glue to ensure stability STEP7.3 (frame Split body) Install (frame_left) to ensure accurate positioning and correct shape matching. It can be bonded with universal glue to ensure stability *After completion, pull out 3 locating pin shafts for standby After this step is completed, test the cooperation between the frame and the slide. If there is jamming, properly polish the chamfer to ensure smooth movement
STEP8.1 1 / 2 glue the corresponding position with universal adhesive Install the slotted countersunk head screw to the corresponding position to ensure beauty STEP8.2 Required parts: pin shaft 2.5x8, pin shaft 2x20, spring 0.2x2.5x15 4 / 5 not at this time, adjust to step 8.3
STEP8.3 Required parts: pin shaft 2.5x18, slotted countersunk screw m2x18, spring 0.2x12x40 Installation direction 2 / 3 install the power rod in sequence to ensure flexible rotation without jamming Install slotted countersunk head screws without over tightening You can perform step 4 / 5 in step 8.2 to install spring_ housing STEP8.4 Install the left and right grip pieces Flat head screw m2.5x5 4pcs
Install the magazine trim base plate Flat countersunk head screw m2x8 STEP8.5 STEP9